| bluerise | mntmn: I wonder what's all needed for the bridge to get sync | 00:25 |
|---|---|---|
| bluerise | I'm executing the commands that the one on your discussion thread did | 00:25 |
| bluerise | But PLL isn't locking | 00:26 |
| bluerise | and link isn't training | 00:26 |
| bluerise | does that mean the mipi dphy isn't configured? hmm | 00:27 |
| bluerise | sigh, maybe I should build a RK3399 SoM :P | 00:31 |
| + chartreuse (~chartreus@S0106f0f249dfd9c3.cg.shawcable.net) | 00:38 | |
| mntmn | bluerise: come on! | 01:02 |
| mntmn | bluerise: the person in the thread uses the nwl dsi and dphy driver that is in uboot, yes | 01:03 |
| mntmn | those drivers are pretty smol | 01:03 |
| mntmn | just a bunch of register pokes... | 01:03 |
| - alex4nde1 (QUIT: Ping timeout: 252 seconds) (~alexander@172.56.42.49) | 01:08 | |
| + alex4nder (~alexander@74.51.16.139) | 01:09 | |
| - chartreuse (QUIT: Quit: Leaving) (~chartreus@S0106f0f249dfd9c3.cg.shawcable.net) | 01:10 | |
| + chartreuse (~chartreus@S0106f0f249dfd9c3.cg.shawcable.net) | 01:29 | |
| chartreuse | Just migrated over to nvme and that was really fast and painless | 01:29 |
| chartreuse | ADATA XPG SX8200 nvme drive seems to be working just fine with the reform. I haven't tested any power saving modes or such just yet. | 01:32 |
| mntmn | cool! i should make a list | 01:38 |
| chartreuse | APSTE is enabled by default as well so that should be working for power savings. Gotta look into how to measure power draw | 01:39 |
| mntmn | you can see total system current on battery in the oled status screen. idk if the nvme itself can show you its power use | 01:40 |
| chartreuse | hexchat is being a bit glitchy, so I guess I need to look into xwayland or such to see what's going on. Or just swap over to irssi or such | 01:41 |
| chartreuse | Right now just sitting around in hexchat I'm drawing 0.29A | 01:42 |
| chartreuse | Has anyone tried lubricating the track ball? Tempted to take it apart and lubricate it with some teflon dry lubricant | 02:02 |
| - alex4nder (QUIT: Ping timeout: 258 seconds) (~alexander@74.51.16.139) | 02:23 | |
| chartreuse | Well I gave lubricating it a try sprayed the dry lube onto a q-tip and applied to the plastic being careful not to go near the sensor. Maybe helped a little bit but not all that much. Most of the scratchiness is likely just the FDM layer lines. | 04:11 |
| chartreuse | Wonder if it's possible to get those teflon(?) balls or such that normal trackballs use and somehow embed them so that the ball isn't resting on the shell directly | 04:12 |
| chartreuse | I think it did help a bit though, and the carrier solvent didn't have an effect on the plastic before it evaporated off | 04:14 |
| swivel | delrin is known to be self-lubricating, could be a good ball material | 05:33 |
| chartreuse | I think the ball material itself is fine, it's going to mainly be the FDM printed socket and retaining ring | 05:50 |
| - erlehmann (QUIT: Ping timeout: 240 seconds) (~erle@dynamic-046-114-036-070.46.114.pool.telefonica.de) | 06:20 | |
| + erlehmann (~erle@dynamic-046-114-035-112.46.114.pool.telefonica.de) | 06:33 | |
| - ggoes (QUIT: Quit: WeeChat 2.3) (~gregf@fsf/staff/ggoes) | 07:04 | |
| - wiedi (QUIT: Ping timeout: 258 seconds) (~wiedi@37.228.191.159) | 07:07 | |
| + ggoes (~gregf@fsf/staff/ggoes) | 07:17 | |
| + wiedi (~wiedi@37.228.191.159) | 09:26 | |
| - doppler (QUIT: Ping timeout: 256 seconds) (~doppler@user/doppler) | 10:07 | |
| + doppler (~doppler@user/doppler) | 10:08 | |
| mntmn | swivel, chartreuse: fwiw the ball is already delrin/POM. | 11:09 |
| mntmn | chartreuse: there is a mod on community.mnt.re where someone used tiny steel ball bearings. you should check it out! | 11:10 |
| - arminweigl (QUIT: Read error: Connection reset by peer) (~arminweig@sourcehut/user/arminweigl) | 11:23 | |
| + arminweigl (~arminweig@sourcehut/user/arminweigl) | 11:25 | |
| + rasmus (~rasmus@c80-217-132-63.bredband.tele2.se) | 11:33 | |
| swivel | nice | 11:40 |
| chartreuse | Yeah I spotted that looking through the forums again. I'm tempted by it. I'll probably order some of those 1.5mm balls | 12:15 |
| chartreuse | Looks like a good mod, since I like having a trackball, though it's not quite as smooth as I'd like with this FDM holder | 12:17 |
| - chartreuse (QUIT: Remote host closed the connection) (~chartreus@S0106f0f249dfd9c3.cg.shawcable.net) | 12:19 | |
| + TadeusTaD (tadeustad@fulu.psifactor.pl) | 12:40 | |
| - rasmus (PART: Disconnected: timeout during receiving) (~rasmus@c80-217-132-63.bredband.tele2.se) | 13:33 | |
| + rasmus (~rasmus@c80-217-132-63.bredband.tele2.se) | 13:34 | |
| + wagga (~wagga@node-1w7jra22ildhx1hkr2m0tolas.ipv6.telus.net) | 14:12 | |
| + darth-cheney (~user@2603-7000-8d00-1f72-0000-0000-0000-1c80.res6.spectrum.com) | 14:53 | |
| darth-cheney | hey all, where can I find the most up to date instructions for migrating to the internal ssd? | 15:04 |
| wagga | I would like to promote a cloned snapshot. man zfs(8) says that the file system must have the 'mount' and 'promote' ability. The file system does have the canmount property set to YES, but I do not see a similar property for promote . Are abilities something different than properties? Or does the lack of such a property indicate that file system | 15:21 |
| wagga | does not have the promote ability? | 15:21 |
| wagga | After further reading, I think the promote ability is referring to permissions. | 15:29 |
| wagga | I checked if my filesystem has the promote permission, but zfs allow tank/root returns no output at all. I just decided to try to promote tank/cloneroot and it worked. So I guess it has the promote ability, or permission. | 15:30 |
| - epilys (PART: Leaving) (~epilys@sic/epilys) | 16:40 | |
| wagga | ahh, sorry, all those messages were meant for #zfsonlinux - LOL! | 16:48 |
| wagga | I ordered my reform by the way. Super excited. | 16:48 |
| wagga | It is going to replace my alenware m17 r4. So, I will be loosing a bit of RAM and some cores :-P Hopefully it won't take too long for additional RAM to become available. | 16:51 |
| wagga | I have to power down and run some errands. CYA! | 16:52 |
| - wagga (QUIT: Quit: Client closed) (~wagga@node-1w7jra22ildhx1hkr2m0tolas.ipv6.telus.net) | 16:53 | |
| mntmn | darth-cheney: check the handbook, advanced section | 17:06 |
| darth-cheney | thanks, duh | 17:11 |
| darth-cheney | got too wrapped up in the online build instructions | 17:11 |
| + alex4nder (~alexander@74.51.16.139) | 17:34 | |
| - rasmus (PART: Disconnected: timeout during receiving) (~rasmus@c80-217-132-63.bredband.tele2.se) | 17:45 | |
| + rasmus (~rasmus@c80-217-132-63.bredband.tele2.se) | 17:46 | |
| - alex4nder (QUIT: Ping timeout: 258 seconds) (~alexander@74.51.16.139) | 17:52 | |
| + alex4nder (~alexander@74.51.16.139) | 17:53 | |
| - erlehmann (QUIT: Quit: Just say no, then the virus can not enter your body without your consent.) (~erle@dynamic-046-114-035-112.46.114.pool.telefonica.de) | 18:23 | |
| - alex4nder (QUIT: Ping timeout: 276 seconds) (~alexander@74.51.16.139) | 18:27 | |
| - darth-cheney (QUIT: Remote host closed the connection) (~user@2603-7000-8d00-1f72-0000-0000-0000-1c80.res6.spectrum.com) | 18:55 | |
| + alex4nder (~alexander@74.51.16.139) | 19:05 | |
| - alex4nder (QUIT: Ping timeout: 272 seconds) (~alexander@74.51.16.139) | 19:27 | |
| - rasmus (PART: Disconnected: closed) (~rasmus@c80-217-132-63.bredband.tele2.se) | 19:51 | |
| + rasmus (~rasmus@c80-217-132-63.bredband.tele2.se) | 19:53 | |
| verx_ | two other drives that I can confirm work great: Intel 660p and WD SN550 | 20:38 |
| - arminweigl (QUIT: Read error: Connection reset by peer) (~arminweig@sourcehut/user/arminweigl) | 21:03 | |
| + arminweigl (~arminweig@sourcehut/user/arminweigl) | 21:04 | |
| bluerise | mntmn: is jtag pin 1 on the side to the som, or on the side to the ethernet? | 21:05 |
| mntmn | bluerise: currently in a bus, you can check with kicad | 21:21 |
| bluerise | pin1 is to the outer side/ethernet (says kicad) | 21:31 |
| bluerise | somehow I can't use jtag.. | 21:37 |
| bluerise | debug port timeout | 21:37 |
| bluerise | oh, don't tell me I need to switch resistors or so for it to work | 21:44 |
| mntmn | bluerise: i have never tested it | 21:50 |
| + wagga (~wagga@node-1w7jra22ildhxpilxbb9o7gyy.ipv6.telus.net) | 21:50 | |
| bluerise | from what I can tell, the SoM shares some Ethernet stuff with the jtag pins | 21:51 |
| bluerise | and the jtag pins are not connected, unless you move some 0R | 21:51 |
| bluerise | so the last hour was rather useless | 21:52 |
| bluerise | apart from updating my lauterbach toolchain | 21:53 |
| mntmn | hmm ja unfortunately they shared some pins on the som | 21:57 |
| mntmn | a bit silly. | 21:57 |
| bluerise | yes | 21:58 |
| mntmn | but afaik i made it so that you can do resistor stuff on the mainboard to make it work theoretically | 21:58 |
| mntmn | would be really interesting for me to see if that works! | 21:58 |
| mntmn | btw i got a mail yesterday from rbz, they got the ls1028a to boot stuff from sd and output to serial. but now they have to do the ddr4 calibration. | 21:59 |
| bluerise | nice | 21:59 |
| bluerise | if you look at the Nitrogen 8M SoM schematics, you'll see on page 8 how the jtag is connected | 21:59 |
| bluerise | RN2 says "NS", RN1 says 0R CAY | 22:00 |
| bluerise | no idea what it means, but NS is probably not soldered? | 22:00 |
| mntmn | i darkly remember something. i will check in a few minutes, just came home | 22:01 |
| bluerise | yeah no worries | 22:05 |
| bluerise | screwed it back up together, guess I'll have to go pack to trying the printf-way | 22:05 |
| - rasmus (PART: Disconnected: timeout during receiving) (~rasmus@c80-217-132-63.bredband.tele2.se) | 22:10 | |
| + rasmus (~rasmus@c80-217-132-63.bredband.tele2.se) | 22:11 | |
| + chartreuse (~chartreus@S0106f0f249dfd9c3.cg.shawcable.net) | 22:14 | |
| + ephase (~ephase@2a01:e0a:168:1211::885) | 22:26 | |
| - rasmus (PART: Disconnected: closed) (~rasmus@c80-217-132-63.bredband.tele2.se) | 22:28 | |
| mntmn | bluerise: sorry for that | 22:32 |
| bluerise | not your fault the SoM is that way :D | 22:32 |
| bluerise | got a backstreet boys ohrwurm | 22:33 |
| mntmn | well, we selected it, but mainly because nobody else agreed to publish schematics to their imx8m som | 22:33 |
| mntmn | bluerise: haha | 22:33 |
| mntmn | also boundary did some imx6 reference design(s) iirc | 22:33 |
| bluerise | SolidRun have afaik, but I'm not sure you'd like the SoM connector | 22:34 |
| mntmn | they did not back then at least... | 22:34 |
| mntmn | normally soldidrun have only partial schematics | 22:34 |
| bluerise | true | 22:35 |
| ephase | hi | 22:49 |
| mntmn | hi | 23:02 |
| ephase | how are you mntmn? | 23:10 |
| mntmn | ok i spent the whole day outside with tina the dog and met some friends, it was long overdue | 23:10 |
| ephase | ha great! I spent time with kids, they wand to go for buying videogames (Geek Papa, geeks kids) | 23:12 |
| + wagga62 (~wagga@node-1w7jra22ildhv2z6kvjy41v6r.ipv6.telus.net) | 23:15 | |
| - wagga (QUIT: Ping timeout: 246 seconds) (~wagga@node-1w7jra22ildhxpilxbb9o7gyy.ipv6.telus.net) | 23:16 | |
| - chartreuse (QUIT: Remote host closed the connection) (~chartreus@S0106f0f249dfd9c3.cg.shawcable.net) | 23:17 | |
| + chartreuse (~chartreus@S0106f0f249dfd9c3.cg.shawcable.net) | 23:17 | |
| * wagga62 -> wagga | 23:19 | |
| mntmn | ephase: good good! | 23:20 |
| ephase | mntmn: I'm writing a blog post about my Reform :) | 23:59 |
Generated by irclog2html.py 2.17.3 by Marius Gedminas - find it at https://mg.pov.lt/irclog2html/!